Speaker has 4 ohm tweeter, 8 ohm mid-woofer, how much ohm should receiver have ?

Discussion in 'Audio Equipment' started by Skybuck Flying, Aug 12, 2009.

  1. Hello,

    Suppose a speaker has the following specifications:

    (input resistance:)
    8 ohm mid-woofer + 4 ohm tweeter + crossover board.

    The receiver has 6 ohm and 8 ohm.

    Is this a good match ? or will the receiver be damaged by the 4 ohm tweeter
    ?

    Please advice.

    Bye,
    Skybuck.
     
    Skybuck Flying, Aug 12, 2009
    #1
    1. Advertisements

  2. "Skybuck Flying" <> schreef in bericht
    news:a0e77$4a83285c$d53372a9$1.nb.home.nl...
    > Hello,
    >
    > Suppose a speaker has the following specifications:
    >
    > (input resistance:)
    > 8 ohm mid-woofer + 4 ohm tweeter + crossover board.
    >
    > The receiver has 6 ohm and 8 ohm.
    >
    > Is this a good match ? or will the receiver be damaged by the 4 ohm
    > tweeter ?
    >
    > Please advice.
    >
    > Bye,
    > Skybuck.
    >
    >

    Test it out. Afterwords you can lawsuit the manufacturer because he does not
    specified this in the manual.
    That what you always want to do.


    Please.... Don't feed this TROLL (his spam will never end)
     
    Henk van den Hof, Aug 12, 2009
    #2
  3. The receiver will have 6 year warranty, so if it dies before that then it
    should not be my problem anyway...

    Just trying to save the world from destruction ! ;) :)

    Bye,
    Skybuck.
     
    Skybuck Flying, Aug 12, 2009
    #3
  4. Skybuck Flying

    Vonkenboer Guest

    TROLL ALERT

    Skybuck Flying had uiteengezet :
    > Hello,
    >


    > Bye,
    > Skybuck.
     
    Vonkenboer, Aug 12, 2009
    #4
  5. Skybuck Flying

    Kai Guest

    On Wed, 12 Aug 2009 22:39:14 +0200, "Skybuck Flying"
    <> wrote:

    >Suppose


    SUPPOSE YOU GO AWAY!


    G O A W A Y ! ! !
     
    Kai, Aug 13, 2009
    #5
  6. "Sonnova" <> wrote in message
    news:...
    > On Wed, 12 Aug 2009 13:39:14 -0700, Skybuck Flying wrote
    > (in article <a0e77$4a83285c$d53372a9$1.nb.home.nl>):
    >
    >> Hello,
    >>
    >> Suppose a speaker has the following specifications:
    >>
    >> (input resistance:)
    >> 8 ohm mid-woofer + 4 ohm tweeter + crossover board.
    >>
    >> The receiver has 6 ohm and 8 ohm.
    >>
    >> Is this a good match ? or will the receiver be damaged by the 4 ohm
    >> tweeter
    >> ?
    >>
    >> Please advice.
    >>
    >> Bye,
    >> Skybuck.
    >>
    >>
    >>

    >
    > Don't worry about it. Impedances are nominal. Rule of thumb: measure DC
    > resistance at speaker cabinet terminals. If speakers are bi-amp/bi
    > wireable,
    > make sure the two sets of cabinet terminals are strapped together. If the
    > DC
    > resistance is around 3 Ohms, use the 4 or 6 Ohm taps on the amplifier. If
    > the
    > resistance is MORE than 6 Ohms, use the 8 Ohm tap. Most 4 ohm speakers
    > will
    > measure about 3.2 Ohms DC, most 8 Ohm systems will measure about 6.8 Ohms
    > of
    > DC resistance. Of course, this only works with cone speaker systems.
    > Speakers
    > like Magneplanars, or electrostatics like Quads or Martin-Logans don't
    > measure the same.


    I am looking at the denon avr 1709 receiver.

    I don't think it has multiple ohm taps...

    But it might have a switch to put it in 6 ohms or 8 ohms...

    Or maybe it's automatic ? (But I don't think so...)

    Anyway satelites with two speakers in them with different ohm ratings... is
    that kinda weird ?

    Hmm...

    If I put it in 6 ohms if possible how would that affect the 8 ohms
    speaker... hmm...

    Bye,
    Skybuck.
     
    Skybuck Flying, Aug 13, 2009
    #6
  7. Re: Speaker has 4 ohm tweeter, 8 ohm mid-woofer, how much ohm shouldreceiver have ?

    On 12 aug, 22:39, "Skybuck Flying" <> wrote:
    > Hello,
    >
    > Suppose a speaker has the following specifications:
    >
    > (input resistance:)
    > 8 ohm mid-woofer + 4 ohm tweeter + crossover board.
    >
    > The receiver has 6 ohm and 8 ohm.
    >
    > Is this a good match ? or will the receiver be damaged by the 4 ohm tweeter
    > ?
    >
    > Please advice.
    >
    > Bye,
    >   Skybuck.


    i guess he choose his own resistance
     
    PA10403-Gerard, Aug 21, 2009
    #7
  8. Re: Speaker has 4 ohm tweeter, 8 ohm mid-woofer, how much ohm shouldreceiver have ?

    PA10403-Gerard schreef:
    > On 12 aug, 22:39, "Skybuck Flying" <> wrote:
    >> Hello,
    >>
    >> Suppose a speaker has the following specifications:
    >>
    >> (input resistance:)
    >> 8 ohm mid-woofer + 4 ohm tweeter + crossover board.
    >>
    >> The receiver has 6 ohm and 8 ohm.
    >>
    >> Is this a good match ? or will the receiver be damaged by the 4 ohm tweeter
    >> ?
    >>
    >> Please advice.
    >>
    >> Bye,
    >> Skybuck.

    >
    > i guess he choose his own resistance


    Please don't crosspost in dutch languaged newsgroups!
    --
    groeten,
    ____________________________Jim©
    ~ OS X really opens up windows ~
     
    James T. Kirk©, Aug 21, 2009
    #8
  9. Re: Speaker has 4 ohm tweeter, 8 ohm mid-woofer, how much ohm shouldreceiver have ?

    PA10403-Gerard wrote:
    > On 12 aug, 22:39, "Skybuck Flying" <> wrote:
    >> Hello,
    >>
    >> Suppose a speaker has the following specifications:
    >>
    >> (input resistance:)
    >> 8 ohm mid-woofer + 4 ohm tweeter + crossover board.
    >>
    >> The receiver has 6 ohm and 8 ohm.
    >>
    >> Is this a good match ? or will the receiver be damaged by the 4 ohm tweeter
    >> ?
    >>
    >> Please advice.
    >>
    >> Bye,
    >> Skybuck.

    >
    > i guess he choose his own resistance

    Put your dick in a mid-woofer that's my advice.
     
    V__i___n_ce__19_7_1_, Aug 26, 2009
    #9

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.

Share This Page