Onkyo TX-2000 light issues

Joined
Jun 19, 2026
Messages
13
Reaction score
0
Location
North Carolina
I have an Onkyo TX-2000 receiver with what I think is a dead pointer lamp, rendering it almost invisible. It's part no 210093 in the user manual, but that part number and the words 'pointer lamp' were added by hand. Furthermore, I'm not able to identify it on the exploded drawing. Has anyone dealt with replacing one of these and could maybe provide some guidance? Thanks!
 
I have an Onkyo TX-2000 receiver with what I think is a dead pointer lamp, rendering it almost invisible. It's part no 210093 in the user manual, but that part number and the words 'pointer lamp' were added by hand. Furthermore, I'm not able to identify it on the exploded drawing. Has anyone dealt with replacing one of these and could maybe provide some guidance? Thanks!

The TX-2000 is a vintage Onkyo receiver, and the pointer lamp (also called an indicator or dial lamp) is typically a small incandescent bulb used to illuminate the tuning pointer or dial scale. The fact that the part number was handwritten in your manual suggests it may have been a service addition rather than an original factory listing, which is why it can be tricky to cross-reference.

Here is what I would suggest. First, carefully remove the lamp (usually accessible once you pull the front panel or dial glass assembly) and measure it physically - note the base type, the overall length, the bulb diameter, and the voltage. On vintage receivers of this era, the lamp is very often a small screw-base (E10) or wedge-base bulb running somewhere between 6V and 14V, with a very low wattage (often 40mA or less). The voltage is usually printed on a service sticker inside or listed in the service manual, which for the TX-2000 may be available on sites like HiFi Engine or Elektrotanya - worth checking if you have not already.

Once you have those physical measurements, generic replacement lamps are widely available from electronics suppliers. Many restorers also take the opportunity to swap the incandescent for a drop-in LED equivalent, which runs cooler and lasts far longer - just be mindful of voltage and current compatibility if you go that route. If you can share the physical dimensions of the bulb once removed, narrowing down the exact replacement becomes straightforward.

This is an automated reply from the Audio Forums AI assistant. AI can make mistakes, so please double-check anything important.

Prefer no AI replies to your own posts? Manage your AI reply settings
 
I certainly appreciate the reply and will work on that in the morning... will let you know what I find, thanks!

Sounds good, take your time with it. Good luck in the morning - those little bulbs can sometimes be fiddly to get to, so good lighting and patience go a long way. Looking forward to hearing what you find!

This is an automated reply from the Audio Forums AI assistant. AI can make mistakes, so please double-check anything important.

Prefer no AI replies to your own posts? Manage your AI reply settings
 
Just finished getting to the bulb and it's a monster, ~ .120" diameter and. 225" long:

onkyo.tx-2000.pointer.bulb.webp


I'm assuming it's what's known as a rice-grain bulb. Naturally there's nothing on the bulb that identifies it, nor are there any specs available, but I did find the following in the manual:
onkyo.tx-2000.illumination.specs.webp

Would it be reasonable to assume that this pointer bulb has the same specs? If so, do you know of a good source for these?
 
Just finished getting to the bulb and it's a monster, ~ .120" diameter and. 225" long:

View attachment 1537

I'm assuming it's what's known as a rice-grain bulb. Naturally there's nothing on the bulb that identifies it, nor are there any specs available, but I did find the following in the manual:
View attachment 1538
Would it be reasonable to assume that this pointer bulb has the same specs? If so, do you know of a good source for these?

Great that you got in there and have a clear look at it! Yes, that does look like a rice grain bulb, and your logic on the specs is reasonable. The dial lamps listed in your manual at 8V 0.15A are a common spec for that era of Japanese receivers, and it would make sense for the pointer lamp to share the same supply voltage at least. The current rating may vary slightly, but 8V 0.15A is a sensible starting assumption.

That said, with no markings on the bulb itself, it is worth measuring the voltage across the lamp socket with your meter before ordering, just to confirm the 8V figure. That takes the guesswork out of it.

For sourcing, a few options worth checking:

Mouser Electronics and Digi-Key both carry small incandescent lamps in that size range, and you can filter by voltage and current. Search for "rice grain lamp 8V" or "midget flange lamp 8V."

justradios.com is a Canadian supplier that specialises in vintage dial and indicator lamps and often stocks exactly this type.

eBay is also worth a search for "8V rice grain bulb" - they turn up in small packs quite readily.

If you do end up going the LED replacement route instead, just be aware you may need a dropping resistor to get the colour and brightness right for a dial application.

This is an automated reply from the Audio Forums AI assistant. AI can make mistakes, so please double-check anything important.

Prefer no AI replies to your own posts? Manage your AI reply settings
 
Back
Top